青草久久精品_久久精品视频天天操_最新亚洲人成无码网WWW电影_一级a性色生活片久久_国产一级婬片91AAA

?

產品推薦

模具行業專用名詞翻譯

來源: 譽格壓鑄    人氣:6112    發布時間: 2020-03-16 

dowel pin 定位梢

draft 拔模錐度

draw bead 張力調整桿

drive bearing 傳動軸承

ejection pad 頂出襯墊

ejector 脫模器

ejector guide pin 頂出導梢

ejector leader busher 頂出導梢襯套

ejector pad 頂出墊

ejector pin 頂出梢

ejector plate 頂出板

ejector rod 頂出桿

ejector sleeve 頂出襯套

ejector valve 頂出閥

eye bolt 環首螺栓

filling core 椿入蕊

film gate 薄膜形澆口

finger pin 指形梢

finish machined plate 角形模板

finish machined round plate 圓形模板

fixed bolster plate 固定側模板

flanged pin 帶凸緣銷

flash gate 毛邊形澆口

flask 上箱

floating punch 浮動沖頭

gate 澆口

gate land 澆口面

gib 凹形拉緊楔

goose neck 鵝頸管

guide bushing 引導襯套

guide pin 導梢

guide post 引導柱

guide plate 導板

guide rail 導軌

head punch 頂頭沖孔

headless punch 直柄沖頭

heavily tapered solid 整體模蕊盒

hose nippler 管接頭

impact damper 緩沖器

injection ram 壓射柱塞

inlay busher 嵌入襯套

inner plunger 內柱塞

inner punch 內沖頭

insert 嵌件

insert pin 嵌件梢

king pin 轉向梢

king pin bush 主梢

一、入水:gate

進入位: gate location

水口形式:gate type

大水口:edge gate

細水口: pin-point gate

水口大?。?/span>gate size

轉水口: switching runner/gate

唧嘴口徑: sprue diameter

二、流道: runner

熱流道: hot runner,hot manifold

熱嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圓形流道:round(full/half runner

流道電腦分析:mold flow analysis

流道平衡:runner balance

熱嘴: hot sprue

熱流道板:hot manifold

發熱管:cartridge heater

探針: thermocouples

插頭: connector plug

插座: connector socket

密封/封料: seal

三、運水:water line

喉塞:line lpug

喉管:tube

塑膠管:plastic tube

快速接頭:jiffy quick connector plug/socker

四、模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

邊釘/導邊:leader pin/guide pin

邊司/導套:bushing/guide bushing

中托司:shoulder guide bushing

中托邊Lguide pin

頂針板:ejector retainner plate

托板: suPPOrt plate

螺絲: screw

管釘:dowel pin

開模槽:ply bar scot

內模管位:core/cavity inter-lock

頂針: ejector pin

司筒:ejector sleeve

司筒針:ejector pin

推板:stripper plate

縮呵:movable core,return core core puller

扣機(尼龍拉勾):nylon latch lock

斜頂:lifter

模胚(架): mold base

上內模:cavity insert

下內模:core insert

行位(滑塊): slide

鑲件:insert

壓座/斜雞:wedge

耐磨板/油板:wedge wear plate

壓條:plate

撐頭: support pillar

唧嘴: sprue bushing

擋板:stop plate

定位圈:locating ring

鎖扣:latch

扣雞:parting lock set

推桿:push bar

栓打螺絲:S.H.S.B

頂板:eracuretun

活動臂:lever arm

分流錐:spure sperader

水口司:bush

垃圾釘:stop pin

隔片:buffle

彈弓柱:spring rod

彈弓:die spring

中托司:ejector guide bush

中托邊:ejector guide pin

鑲針:pin

銷子:dowel pin

波子彈弓:ball catch

喉塞: pipe plug

鎖模塊:lock plate

斜頂:angle from pin

斜頂桿:angle ejector rod

尼龍拉勾:parting locks

活動臂:lever arm

復位鍵、提前回桿:early return bar

氣閥:valves

斜導邊:angle pin

術語:terms

承壓平面平衡:parting surface support balance

模排氣:parting line venting

回針碰料位:return pin and cavity interference

??偢叱銎C(jī)規格:mold base shut hight

頂針碰運水:water line interferes withejector pin

料位出上/下模:part from cavith (core) side

模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

不準用鑲件: Do not use (core/cavity) insert

用鈹銅做鑲件: use beryllium copper insert

初步(正式)模圖設計:preliinary (final) mold design

反呵:reverse core

彈弓壓縮量:spring compressed length

穩定性好:good stability,stable

強度不夠:insufficient rigidity

均勻冷卻:even cooling

扣模:sticking

熱膨脹:thero expansion

公差:tolorance

銅公(電極):copper electrode

dowel pin 定位梢

draft 拔模錐度

draw bead 張力調整桿

drive bearing 傳動軸承

ejection pad 頂出襯墊

ejector 脫模器

ejector guide pin 頂出導梢

ejector leader busher 頂出導梢襯套

ejector pad 頂出墊

ejector pin 頂出梢

ejector plate 頂出板

ejector rod 頂出桿

ejector sleeve 頂出襯套

ejector valve 頂出閥

eye bolt 環首螺栓

filling core 椿入蕊

film gate 薄膜形澆口

finger pin 指形梢

finish machined plate 角形模板

finish machined round plate 圓形模板

fixed bolster plate 固定側模板

flanged pin 帶凸緣銷

flash gate 毛邊形澆口

flask 上箱

floating punch 浮動沖頭

gate 澆口

gate land 澆口面

gib 凹形拉緊楔

goose neck 鵝頸管

guide bushing 引導襯套

guide pin 導梢

guide post 引導柱

guide plate 導板

guide rail 導軌

head punch 頂頭沖孔

headless punch 直柄沖頭

heavily tapered solid 整體模蕊盒

hose nippler 管接頭

impact damper 緩沖器

injection ram 壓射柱塞

inlay busher 嵌入襯套

inner plunger 內柱塞

inner punch 內沖頭

insert 嵌件

insert pin 嵌件梢

king pin 轉向梢

king pin bush 主梢

difference quantity差異量

cause analysis原因分析

raw materials原料

materials物料

finished product成品

semi-finished product半成品

packing materials包材

good product/accepted goods/ accepted parts/good parts良品

defective product/non-good parts不良品

disposed goods處理品

warehouse/hub倉庫

on way location在途倉

oversea location海外倉

spare parts physical inventory list備品盤點清單

spare molds location模具備品倉

skid/pallet棧板

tox machine自鉚機

wire EDM線割

EDM放電機

coil stock卷料

sheet stock片料

tolerance工差

score=groove壓線

cam block滑塊

pilot導正筒

trim剪外邊

pierce剪內邊

drag form壓鍛差

pocket for the punch head掛鉤槽

slug hole廢料孔

feature die公母模

expansion dwg展開圖

radius半徑

shim(wedge)楔子

torch-flame cut火焰切割

set screw止付螺絲

form block折刀

stop pin定位銷

round pierce punch=die button圓沖子

shape punch=die insert異形子

stock locater block定位塊

under cut=scrap chopper清角

active plate活動板

baffle plate擋塊

cover plate蓋板

male die公模

female die母模

groove punch壓線沖子

air-cushion eject-rod氣墊頂桿

spring-box eject-plate彈簧箱頂板

bushing block襯套

insert 入塊

club car高爾夫球車

capability能力

parameter參數

factor系數

phosphate皮膜化成

viscosity涂料粘度

alkalidipping脫脂

main manifold主集流脈

bezel斜視規

blanking穿落模

dejecting頂固模

demagnetization去磁;消磁

high-speed transmission高速傳遞

heat dissipation熱傳

rack上料

degrease脫脂

rinse水洗

alkaline etch齡咬

desmut剝黑膜

D.I. rinse純水次

Chromate鉻酸處理

Anodize陽性處理

seal封孔

revision版次

part number/P/N料號

good products良品

scraped products報放心品

defective products不良品

finished products成品

disposed products處理品

barcode條形碼

flow chart流程窗體

assembly組裝

stamping沖壓

molding成型

spare parts=buffer備品

coordinate坐標

dismantle the die折模

auxiliary fuction輔助功能

poly-line多義線

heater band 加熱片

thermocouple熱電偶

sand blasting噴沙

grit 砂礫

derusting machine除銹機

degate打澆口

dryer烘干機

induction感應

induction light感應光

response=reaction=interaction感應

ram連桿

edge finder巡邊器

concave

convex

short射料不足

nick缺口

speck瑕疪

shine亮班

splay 銀紋

gas mark焦痕

delamination起鱗

cold slug冷塊

blush 導色

gouge溝槽;鑿槽

satin texture段面咬花

witness line證示線

patent專利

grit沙礫

granule=peuet=grain細粒

grit maker抽粒機

cushion緩沖

magnalium鎂鋁合金

magnesium鎂金

metal plate鈑金

lathe

mill

plane

grind

drill

boring

blinster氣泡

fillet;嵌邊

through-hole form通孔形式

voller pin formality滾針形式

cam driver鍘楔

shank摸柄

crank shaft曲柄軸

augular offset角度偏差

velocity速度

production tempo生產進度現狀

torque扭矩

spline=the multiple keys花鍵

quenching淬火

tempering回火

annealing退火

carbonization碳化

alloy合金

tungsten high speed steel鎢高速的

moly high speed steel鉬高速的

organic solvent有機溶劑

bracket小磁導

liaison聯絡單

volatile揮發性

resistance電阻

ion離子

titrator滴定儀

beacon警示燈

coolant冷卻液

crusher破碎機

模具工程類

plain die簡易模

pierce die沖孔模

forming die成型模

progressive die連續模

gang dies復合模

shearing die剪邊模

riveting die鉚合模

pierce沖孔

forming成型(抽凸,沖凸)

draw hole抽孔

bending折彎

trim切邊

emboss凸點

dome凸圓

semi-shearing半剪

stamp mark沖記號

deburr or coin壓毛邊

punch riveting沖壓鉚合

side stretch側沖壓平

reel stretch卷圓壓平

groove壓線

blanking下料

stamp letter沖字(料號)

shearing剪斷

tick-mark nearside正面壓印

tick-mark farside反面壓印

沖壓名稱類

extension dwg展開圖

procedure dwg工程圖

die structure dwg模具結構圖

material材質

material thickness料片厚度

factor系數

upward向上

downward向下

press specification沖床規格

die height range適用模高

die height閉模高度

burr毛邊

gap間隙

weight重量

total wt.總重量

punch wt.上模重量

五金零件類

inner guiding post內導柱

inner hexagon screw內六角螺釘

dowel pin固定銷

coil spring彈簧

lifter pin頂料銷

eq-height sleeves=spool等高套筒

pin

lifter guide pin浮升導料銷

guide pin導正銷

wire spring圓線彈簧

outer guiding post外導柱

stop screw止付螺絲

located pin定位銷

outer bush外導套

模板類

top plate上托板(頂板)

top block上墊腳

punch set上模座

punch pad上墊板

punch holder上夾板

stripper pad脫料背板

up stripper上脫料板

male die公模(凸模)

feature die公母模

female die母模(凹模)

upper plate上模板

lower plate下模板

die pad下墊板

die holder下夾板

die set下模座

bottom block下墊腳

bottom plate下托板(底板)

stripping plate內外打(脫料板)

outer stripper外脫料板

inner stripper內脫料板

lower stripper下脫料板

零件類

punch沖頭

insert入塊(嵌入件)

deburring punch壓毛邊沖子

groove punch壓線沖子

stamped punch字模沖子

round punch圓沖子

special shape punch異形沖子

bending block折刀

roller滾軸

baffle plate擋塊

located block定位塊

supporting block for location定位支承塊

air cushion plate氣墊板

air-cushion eject-rod氣墊頂桿

trimming punch切邊沖子

stiffening rib punch = stinger 加強筋沖子

ribbon punch壓筋沖子

reel-stretch punch卷圓壓平?jīng)_子

guide plate定位板

sliding block滑塊

101個熱處理常用英文詞匯

1. indication 缺陷

2. test specimen 試樣

3. bar 棒材

4. stock 原料

5. billet 方鋼,鋼方坯

6. bloom 鋼坯,鋼錠

7. section 型材

8. steel ingot 鋼錠

9. blank 坯料,半成品

10. cast steel 鑄鋼

11. nodular cast iron 球墨鑄鐵

12. ductile cast iron 球墨鑄鐵

13. bronze 青銅

14. brass 黃銅

15. copper 合金

16. stainless steel不銹鋼

17. decarburization 脫碳

18. scale 氧化皮

19. anneal 退火

20. process anneal 進行退火

21. quenching 淬火

22. normalizing 正火

23. Charpy impact text 夏比沖擊試驗

24. fatigue 疲勞

25. tensile testing 拉伸試驗

26. solution 固溶處理

27. aging 時效處理

28. Vickers hardness維氏硬度

29. Rockwell hardness 洛氏硬度

30. Brinell hardness 布氏硬度

31. hardness tester硬度計

32. descale 除污,除氧化皮等

33. ferrite 鐵素體

34. austenite 奧氏體

35. martensite馬氏體

36. cementite 滲碳體

37. iron carbide 滲碳體

38. solid solution 固溶體

39. sorbite 索氏體

40. bainite 貝氏體

41. pearlite 珠光體

42. nodular fine pearlite/ troostite屈氏體

43. black oxide coating 發黑

44. grain 晶粒

45. chromium

46. cadmium

47. tungsten

48. molybdenum

49. manganese

50. vanadium

51. molybdenum

52. silicon

53. sulfer/sulphur

54. phosphor/ phosphorus

55. nitrided 氮化的

56. case hardening 表面硬化,表面淬硬

57. air cooling 空冷

58. furnace cooling 爐冷

59. oil cooling 油冷

60. electrocladding /plating 電鍍

61. brittleness 脆性

62. strength 強度

63. rigidity 剛性,剛度

64. creep 蠕變

65. deflection 撓度

66. elongation 延伸率

67. yield strength 屈服強度

68. elastoplasticity 彈塑性

69. metallographic structure 金相組織

70. metallographic test 金相試驗

71. carbon content 含碳量

72. induction hardening 感應淬火

73. impedance matching 感應淬火

74. hardening and tempering 調質

75. crack 裂紋

76. shrinkage 縮孔,疏松

77. forging 鍛(件)

78. casting 鑄(件)

79. rolling 軋(件)

80. drawing 拉(件)

81. shot blasting 噴丸(處理)

82. grit blasting 噴鋼砂(處理)

83. sand blasting 噴砂(處理)

84. carburizing 滲碳

85. nitriding 滲氮

86. ageing/aging 時效

87. grain size 晶粒度

88. pore 氣孔

89. sonim 夾砂

90. cinder inclusion 夾渣

91. lattice晶格

92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性

93. spectrum analysis光譜分析

94. heat/thermal treatment 熱處理

95. inclusion 夾雜物

96. segregation 偏析

97. picking 酸洗,酸浸

98. residual stress 殘余應力

99. remaining stress 殘余應力

100. relaxation of residual stress 消除殘余應力

101. stress relief 應力釋放

機械類常用英語:沖壓模具-零件類

punch沖頭

insert入塊(嵌入件)

deburring punch壓毛邊沖子

groove punch壓線沖子

stamped punch字模沖子

round punch圓沖子

special shape punch異形沖子

bending block折刀

roller滾軸

baffle plate擋塊

located block定位塊

supporting block for location定位支承塊

air cushion plate氣墊板

air-cushion eject-rod氣墊頂桿

trimming punch切邊沖子

stiffening rib punch = stinger 加強筋沖子

ribbon punch壓筋沖子

reel-stretch punch卷圓壓平?jīng)_子

guide plate定位板

sliding block滑塊

sliding dowel block滑塊固定塊

active plate活動板

lower sliding plate下滑塊板

upper holder block上壓塊

upper mid plate上中間板

spring box彈簧箱

spring-box eject-rod彈簧箱頂桿

spring-box eject-plate彈簧箱頂板

bushing bolck襯套

cover plate蓋板

guide pad導料塊

landed plunger mold 有肩柱塞式模具

burnishing die 擠光模

landed positive mold 有肩全壓式模具

button die 鑲?cè)胧綀A形凹模

loading shoe mold 料套式模具

center-gated mold 中心澆口式模具

loose detail mold 活零件模具

chill mold 冷硬用鑄模

loose mold 活動式模具

clod hobbing 冷擠壓制模

louvering die 百葉窗沖切模

composite dies 復合模具

manifold die 分歧管模具

counter punch 反凸模

modular mold 組合式模具

double stack mold 雙層模具

multi-cavity mold 多模穴模具

electroformed mold 電鑄成形模

multi-gate mold 復式澆口模具

expander die 擴徑模

offswt bending die 雙折冷彎模具

extrusion die 擠出模

palletizing die 疊層模

family mold 反套制品模具

plaster mold 石膏模

blank through dies 漏件式落料模

porous mold 通氣性模具

duplicated cavity plate 復板模

positive mold 全壓式模具

fantail die 扇尾形模具

pressure die 壓緊模

fishtail die 魚尾形模具

profile die 輪廓模

flash mold 溢料式模具

progressive die 順序模

gypsum mold 石膏鑄模

protable mold 手提式模具

hot-runner mold 熱流道模具

prototype mold 雛形試驗?zāi)>?/span>

ingot mold 鋼錠模

punching die 落料模

lancing die 切口模

aising(embossing) 壓花起伏成形

re-entrant mold 倒角式模具

sectional die 拼合模

runless injection mold 無流道冷料模具

sectional die 對合模具

segment mold 組合模

semi-positive mold 半全壓式模具

shaper 定型模套

single cavity mold 單腔模具

solid forging die 整體鍛模

split forging die 拼合鍛模

split mold 雙并式模具

sprueless mold 無注道殘料模具

squeezing die 擠壓模

stretch form die 拉伸成形模

sweeping mold 平刮鑄模

swing die 振動模具

three plates mold 三片式模具

trimming die 切邊模

unit mold 單元式模具

universal mold 通用模具

unscrewing mold 退扣式模具

yoke type die 軛型模

塑料成形模具   mould for plastics      

熱塑性塑料模   mould for thermoplastics      

熱固性塑料模   mould for thermosets      

壓縮模   compression mould      

壓注模、傳遞模   transfer mould      

注射模   injection mould      

熱塑性塑料注射模   injection mould for thermoplastics    

熱固性塑料注射模   injection mould for thermoses      

成形零件        

定模   stationary mould fixed half      

動模   movable mould moving half      

定模座板   fixed clamp plate, top clamping plate. top plate      

動模座板   moving clamp plate. bottom clamping plate. bottom plate      

上模座板   upper clamping plate      

下模座板   lower clamping plate      

凹模固定板   cavity-retainer plate      

型芯固定板   core-retainer plate      

凸模固定板   punch-retainer plate      

模套   chase. bolster. frame      

支承板   backing plate. supprr plate      

墊塊   spacer parallel      

支架   ejector housing. mould base leg  

模具工程常用詞匯英漢對照

die 模具

figure file, chart file圖檔

cutting die, blanking die沖裁模

progressive die, follow (-on)die連續模

compound die復合模

punched hole沖孔

panel board鑲塊

to cutedges=side cut=side scrap切邊

to bending折彎

to pull, to stretch拉伸

Line streching, line pulling線拉伸

engraving, to engrave刻印

upsiding down edges翻邊

to stake鉚合

designing, to design設計

design modification設計變化

die block模塊

folded block折彎塊

sliding block滑塊

location pin定位銷

lifting pin頂料銷

die plate, front board模板

padding block墊塊

stepping bar墊條

upper die base上模座

lower die base下模座

upper supporting blank上承板

upper padding plate blank上墊板

spare dies模具備品

spring 彈簧

bolt螺栓

document folder文件夾

file folder資料夾

to put file in order整理資料

spare tools location手工備品倉

first count初盤人

first check初盤復棹人

second count 復盤人

second check復盤復核人

equipment設備

waste materials廢料

work in progress product在制品

casing = containerazation裝箱

quantity of physical invetory second count 復盤點數量

quantity of customs count會計師盤,點數量

the first page第一聯

filed by accounting department for reference會計部存查

end-user/using unit(department)使用單位

summary of year-end physical inventory bills年終盤點截止單據匯總表

bill name單據名稱

This sheet and physical inventory list will be sent to accountingdepartment together (Those of NHK will be sent to financialdepartment).本表請與盤點清冊一起送會計部-(NHK廠區送財會部)

Application status records of year-end physical inventory List andphysical inventory card 年終盤點卡與清冊使用-狀況明細表

blank and waste sheet NO.空白與作廢單號

plate電鍍

mold成型

material for engineering mold testing工程試模材料

not included in physical inventory不列入盤點

sample樣品

incoming material to be inspected進貨待驗

description品名

steel/rolled steel鋼材

material statistics sheet

物料統計明細表

meeting minutes會議記錄

meeting type 會別

distribution department分發單位

location地點

chairman主席

present members出席人員

subject主題

conclusion結論

decision items決議事項

responsible department負責單位

pre-fixed finishing date預定完成日

approved by / checked by / prepared by核準/審核/承辦

PCE assembly production schedule sheet,PCE組裝廠生產排配表

model機鍾

work order工令

revision版次

remark備注

production control confirmation生產確認

checked by初審

approved by核準

department部門

stock age analysis sheet

庫存貨齡分析表

on-hand inventory現有庫存

available material良品可使用

obsolete material良品已呆滯

to be inspected or reworked待驗或重工

total合計

cause description原因說明

part number/ P/N 料號

type形態

item/group/class類別

quality品質

prepared by制表

notes說明

year-end physical inventory difference analysis sheet年終盤點差異分析表

physical inventory盤點數量

physical count quantity帳面數量

difference quantity差異量

cause analysis原因分析

raw materials原料

materials物料

finished product成品

semi-finished product半成品

packing materials包材

good product/accepted goods/ accepted parts/good parts良品

defective product/non-good parts不良品

disposed goods處理品

warehouse/hub倉庫

on way location在途倉

oversea location海外倉

spare parts physical inventory list備品盤點清單

spare molds location模具備品倉

skid/pallet棧板

tox machine自鉚機

wire EDM線割

EDM放電機

coil stock卷料

sheet stock片料

tolerance工差

score=groove壓線

cam block滑塊

pilot導正筒

trim剪外邊

pierce剪內邊

drag form壓鍛差

pocket for the punch head掛鉤槽

slug hole廢料孔

feature die公母模

expansion dwg展開圖

radius半徑

shim(wedge)楔子

torch-flame cut火焰切割

set screw止付螺絲

form block折刀

stop pin定位銷

round pierce punch=die button圓沖子

shape punch=die insert異形子

stock locater block定位塊

under cut=scrap chopper清角

active plate活動板

baffle plate擋塊

cover plate蓋板

male die公模

female die母模

groove punch壓線沖子

air-cushion eject-rod氣墊頂桿

spring-box eject-plate彈簧箱頂板

bushing block襯套

insert 入塊

club car高爾夫球車

capability能力

parameter參數

factor系數

phosphate皮膜化成

viscosity涂料粘度

alkalidipping脫脂

main manifold主集流脈

bezel斜視規

blanking穿落模

dejecting頂固模

demagnetization去磁;消磁

標簽: 模具行業